|قطر سوراخ مته:||2000 تا 3200 میلیمتر||سرعت چرخشی:||0.6 / 1.0 / 1.8 دور در دقیقه|
|فشار کشیدن سکته مغزی:||750 میلیمتر||وزن:||96 تن|
|موتور مدل:||Cummins QSM11-335x2||قدرت موتور:||2x272 / 1800 کیلووات ساعت / دور در دقیقه|
|مصرف سوخت موتور:||2 * 216 گرم / کیلو وات (حداکثر توان قدرت)||حالت کنترل:||کنترل از راه دور سیمی|
|وزن بسته هیدرولیک:||13 تن||رنگ:||سبز|
Biggest Type Casing Rotator for 2000 to 3200mm Pile Dia. KTR3205H
TYSIM Casing Rotator, Special use wedge clampling device.
Being Compared with the traditional clampling mechanism, it can clamp the casing no matter at what position, and keep the vertical accuracy of the casing; and the larger drawing resistance of casing causes greater lamp force.
(1) No noise, no vibration, and high safety.
(2) Without mud, clean working surface, good environmental friendliness, avoiding the possibility for mud to enter the concrete, high pile quality, enhancing the bond stress of concrete to the steel bar;
(3) During construction drilling, the characteristics of stratum and rock can be directly distinguished;
(4) The drilling speed is fast and reaches about 14m/h for the general soil layer;
(5) The drilling depth is large and reaches about 80m according to the situation of soil layer;
(6) The hole forming verticality is easy to master, which can be accurate to 1/500;
(7) No hole collapse will be caused, and the hole forming quality is high;
(8) The hole forming diameter is standard, with little filling factor. Being compared with other hole forming methods, it can save a lot of concrete usage;
(9) The hole clearing is thorough and fast. The drilling mud at the hole bottom can be clear to about 3.0cm.
|Drilling Diameter||2000-3200 mm|
|Lower Pressure of sleeve||Max. 1100kN+Dead Weight 600 kN|
|Pulling fore of sleeve||7237kN, Instantaneous 8370 kN|
|Pressure pulling stroke||750 mm|
|Parameters of Hydraulic power station|
|Engine Model||Cummins QSM11-335x2|
|Engine Power||2x272/1800 kw/rpm|
|Fuel Consumption of Engine||2x216 g/kwh( Max. power rate)|
|Control Mode||Wired remote control|
Use for different types construction:
(1) Foundation pile, continuous wall
Foundation piles for high-speed rail, road and bridge and house building;
Articulation pile constructions which are required to be excavated, such as subway platforms, underground architectures, continuous walls.
Water retaining wall of reservoir reinforcement.
(2)Drilling gravels, boulders and karst caves
It is allowable to conduct the foundation pile construction at mountain lands with gravel and boulder formations.
It is allowable to conduct operation and cast the foundation piles at the thick quicksand formation and necking down stratum or the filling layer.
Conduct rock-socketed drilling to the rock stratum, cast the foundation pile.
(3) Clear the underground obstructions
During the urban construction and bridge rebuilding, the obstructions such as the steel reinforced concrete pile, steel pipe pile, H steel pile, pc pile and wood pile can be cleared directly, and cast the foundation pile on the spot.
(4) Cut the rock stratum
Conduct the rock-socketed drilling to the cast-in-place piles.
Drill through-holes on the rock bed(shafts and ventilation holes).
(5) Deep excavation
Conduct the in-place casting or steel pipe pile inserting for the deep foundation improvement.
Excavate deep wells for construction use in the constructions of reservoir and tunnel.